Files
Scavenger Frame
Scavenger Frame
instructions to follow. i think these are all the current parts. rear door and utility arms are not included. as currently doing magnetic mounts. rear door supports are not included as doing magnetic mounts. these are all in 6mm thick parts for 3d print not for aluminium cutting as i was going to get it cut before i decided to semi retire. bread pans are not included until i work out a hinge mount. dome motor mount is done but i need to find the correct file.
Files
Files
- Attachments
-
scav-frame-top-suppx1.stl- optional top ring support (3mm)
- (82.31 KiB) Downloaded 42 times
-
- scav-frame-botx1.stl
- bottom plate
- (183.68 KiB) Downloaded 44 times
-
- scav-frame-topx1.stl
- top plate
- (264.54 KiB) Downloaded 47 times
-
- scav-frame-midx1.stl
- mid ring
- (122.54 KiB) Downloaded 54 times
-
- scav-frame-up-hzsupx2.stl
- side leg mount
- (132.11 KiB) Downloaded 64 times
-
- scav-frame-up-lowerx2.stl
- lower side support
- (9.65 KiB) Downloaded 43 times
-
- scav-frame-side -skin-mountx2.stl
- side skin mount
- (12.19 KiB) Downloaded 51 times
-
- scav-frame-speakerx1.stl
- speaker mount
- (56.53 KiB) Downloaded 50 times
-
- scav-frame-fnt-longx2.stl
- long front supports
- (24.3 KiB) Downloaded 49 times
-
- scav-frame-rear-longx2.stl
- long rear supports
- (22.15 KiB) Downloaded 42 times
-
- scav-frame-fnt-shortx2.stl
- front vents supports
- (15.12 KiB) Downloaded 44 times
-
- scav-frame-fnt-topventx1.stl
- front top vent
- (53.99 KiB) Downloaded 40 times
Re: Scavenger Frame
Rough frame assembly guide. of course it will change with thicker material to how i did the OG version but thats why we test and test. thanks everyone.
- Attachments
-
scav-frame-assembly.pdf- (660.35 KiB) Downloaded 51 times
Re: Scavenger Frame
here are the rear door files. no magnet holes yet so will wait for some advise on where to put them. the side of the door has about 6mm (0.25") for 2 3mm (0.125") magnets. i thinking 1 on the frame side 1 on the door. 1 magnet will need to be reversed so it will stick. thin washers can be used for padding it out. the x# at the end means how many times to print.
- Attachments
-
- scav-door-topsx3.stl
- (28.01 KiB) Downloaded 46 times
-
- scav-door-botx1.stl
- (37.58 KiB) Downloaded 40 times
-
- scav-frame-midx1.stl
- (122.54 KiB) Downloaded 59 times
-
- scav-door-upx2.stl
- (42.86 KiB) Downloaded 42 times
Re: Scavenger Frame
the breadpans... still need to make allowances for the hinges... i have designed a hinge extension but these give me feedback for if a tool can be placed inside
- Attachments
-
- BREAD-PAN1x2.stl
- (27.43 KiB) Downloaded 49 times
-
- BREAD-PAN2x2.stl
- (13.17 KiB) Downloaded 66 times
Re: Scavenger Frame
utility arm box.... this one is a doozie still. still thinking about how to mount... magnets or nut and bolt at the base... or both. only thinking magnets could pull out when some civilian yanks on the arms too much when shaking hands.... both will mean not all the weight will be on the bolt as magnets will give some resistance!! feed back welcome on everything!!
- Attachments
-
- scav-frame-utl-mid-hix1.stl
- (128.01 KiB) Downloaded 48 times
-
- scav-frame-utl-lowx1.stl
- (56.72 KiB) Downloaded 59 times
-
- scav-frame-utl-hix1.stl
- (35.04 KiB) Downloaded 40 times
-
- scav-frame-utl-vertbigx2.stl
- (24.69 KiB) Downloaded 83 times
